compress
Install FUSE and the fusecompress compressed filesystem
- Command:
/go/compress - Category: System
- Required option: None
- Output: Progress bar and package manager output (also logged to
/var/log/go/compress.log) - Last updated: 2026-11-20
On this page: Overview · Quick start · Syntax · Output · Examples · Troubleshooting · Details · See also
Overview
/go/compress installs the tools needed to use a compressed filesystem on the server. It installs FUSE (Filesystem in Userspace) and fusecompress, which transparently compresses files written to a mounted folder and decompresses them when they are read. A typical use is a backup folder such as /backup, where compression saves disk space.
The command only installs the tools. It doesn't mount anything or change any existing folder.
[!NOTE] On AlmaLinux, Rocky, CentOS, Red Hat, and Fedora the command installs
fusecompressitself. On Debian and Ubuntu it installs only FUSE and the libraries needed to build it, sofusecompressis not available afterwards. See Supported systems.
Quick start
# Install FUSE and fusecompress
/go/compress
Syntax
/go/compress
The command takes no options or arguments. Any you pass are ignored (they are only written to the log).
Run it as root. On Debian and Ubuntu the package installation steps are not run with sudo.
Output
The command shows a progress bar titled Installing FUSE & Compressed Filesystem Tools, followed by the output of the package manager and, on RHEL-family systems, of the build.
| Situation | What you see |
|---|---|
| Supported system | Package manager output, plus build output if fusecompress has to be compiled. |
| Unsupported operating system | Nothing beyond the progress bar. |
The command prints no summary and sets no exit code of its own, so a failed package install isn't reported. Check the output, and confirm with command -v fusecompress.
Every run is logged with a timestamp, for example [Nov 20 09:15:02]# compress, to /var/log/go/compress.log.
Examples
# Install the tools
/go/compress
# Check that fusecompress is available
command -v fusecompress
# Mount a folder with transparent compression (example from the script)
mkdir -p /backup
fusecompress -o allow_other /backup
# Mount it automatically at boot: add this line to /etc/fstab
/backup /backup fuse.fusecompress allow_other,defaults 0 0
# Unmount it
fusermount -u /backup
The mount examples are from comments in the script. The command doesn't run them. Test them on a non-critical folder first. A FUSE filesystem uses more CPU and is slower than a native one.
Troubleshooting
| Symptom | Likely cause | Fix |
|---|---|---|
fusecompress: command not found on Debian or Ubuntu |
The command only installs build dependencies there. | Build fusecompress from source (see Details). |
Unable to locate package lzo2-dev or libxz-dev |
These package names don't exist on all releases. | Install the equivalent development packages manually, typically liblzo2-dev and liblzma-dev. |
No match for argument: fuse-compress or fuse-zip on RHEL-family systems |
The package isn't in the enabled repositories. | Enable EPEL if needed. The command builds fusecompress from source in any case. |
git: command not found, or gcc or make not found |
The build tools aren't installed. | Install git, gcc, and make, then run the command again. |
git clone fails |
The server can't reach GitHub. | Check the server's network and DNS settings. |
| Nothing happens | The operating system isn't supported. | Supported: AlmaLinux, Rocky, CentOS, Red Hat, Fedora, Debian, Ubuntu. |
Permission denied or Could not open lock file on Debian or Ubuntu |
You aren't running as root. | Run the command as root. |
| The mount is gone after a reboot | Mounts made by hand aren't permanent. | Add the /etc/fstab line from Examples. |
/usr/local/goadmio/tmp/fusecompress is using space |
The build files are kept after installing. | Delete the folder, or run clean. |
Details
Supported systems
| Family | Systems | What is installed |
|---|---|---|
| RHEL | AlmaLinux, Rocky, CentOS, Red Hat, Fedora | FUSE, fuse-zip, and fuse-compress from the repositories. If fusecompress is still missing, it is built from source and installed to /usr/local. |
| Debian | Debian, Ubuntu | FUSE, the FUSE development files, and the compression development libraries. fusecompress is not installed. |
The operating system is read from /usr/local/goadmio/linux/os.db. On any other system the command does nothing.
RHEL-family steps
- Installs
fuse,fuse-zip, andfuse-compresswithdnf. - If
fusecompressis still not available:- Installs the build tools and libraries
autoconf,libtool,fuse-devel,zlib-devel,bzip2-devel,lz4-devel,lzo-devel, andxz-devel. - Clones the
fusecompresssource fromhttps://github.com/FS-make-simple/fusecompress.gitinto/usr/local/goadmio/tmp/fusecompress. - Runs
./autogen.shand./configure --prefix=/usr/local. - Compiles with
makeusing all CPU cores, then runsmake installandldconfig.
- Installs the build tools and libraries
The build needs git, a C compiler, and make, which the command doesn't install. Running the command again is safe: the build is skipped once fusecompress is available.
Debian and Ubuntu steps
- Updates the package lists with
apt update. - Installs
fuse,libfuse-dev,zlib1g-dev,libbz2-dev,liblz4-dev,lzo2-dev, andlibxz-dev.
On Debian and Ubuntu, fusecompress has to be downloaded and built manually, using the same source and build steps as on the RHEL family.
See also
| Command | Description |
|---|---|
clean |
Delete old backups, trash, session files, and expired mail to free up disk space |
backup |
Create a backup for all GoAdmio accounts (local and remote) |
storage |
Auto-mount the /storage folder on boot using rclone |
s3 |
Mount an S3 bucket on a GoAdmio server |
package |
Install all base packages required by GoAdmio |